Home / All Calculators / Concrete Slab Cost Calculator

Concrete Slab Cost Calculator

Use this Concrete Slab Cost Calculator to find out how many cubic yards or bags of concrete your slab needs, and what a patio, driveway or shed pad will cost to have installed.

How this calculator works

The calculator multiplies your slab area by a typical installed price per square foot for the finish you pick, scales it for thickness, and adds optional gravel base preparation. It also converts your dimensions into cubic yards and bags of premixed concrete, with 10% extra for waste and uneven ground.

Typical concrete slab cost by size and finish

Typical installed prices for a 4 inch slab in an average-cost area, without gravel base preparation.

Slab sizeAreaBroom finishColoredStamped
10 × 10 ft100 sq ft$800$900$1,500
12 × 12 ft144 sq ft$1,150$1,300$2,160
20 × 20 ft400 sq ft$3,200$3,600$6,000
24 × 24 ft576 sq ft$4,610$5,180$8,640
30 × 30 ft900 sq ft$7,200$8,100$13,500

What affects the cost

  • Slab size. Cost scales with square footage, but very small slabs cost more per square foot because crews and concrete suppliers have minimum charges.
  • Thickness. A 4 inch slab suits patios and walkways. Driveways and garage floors are usually 5 to 6 inches and cost more because they need more concrete.
  • Finish. A plain broom finish is the cheapest. Colored and stamped concrete add materials and skilled labor.
  • Site preparation. Excavation, grading, a compacted gravel base and forms add cost. Poor soil or a sloped site adds more.
  • Reinforcement. Rebar or wire mesh adds strength and is common for driveways and heavy loads.
  • Access and removal. Hard-to-reach sites may need a pump truck or wheelbarrows, and tearing out an old slab is a separate charge.

Tips

  • Order about 10% more concrete than your measurements say. Running short mid-pour is expensive.
  • Ask for a price per square foot and a total, including base, forms, finishing and cleanup.
  • Check whether your area needs a permit, especially for driveways and slabs that support structures.
  • Pouring in mild weather gives the concrete the best chance to cure well.
  • Seal exposed slabs after curing to protect against stains and freeze-thaw damage.

Frequently asked questions

How many bags of concrete do I need?

An 80 lb bag of premix yields about 0.6 cubic feet and a 60 lb bag about 0.45. Divide the cubic feet of concrete you need by that yield and round up. The calculator shows both counts, with 10% extra included. Bags suit small jobs such as footings and small pads. For larger slabs, ready-mix delivered by truck is usually easier.

How do I calculate cubic yards of concrete?

Multiply length by width by thickness (all in feet, so divide inches by 12) and divide by 27. Add about 10% for waste. The calculator does this for you.

How much does a 20x20 concrete slab cost?

A 20 by 20 ft slab is 400 sq ft. At typical installed prices, a plain 4 inch slab commonly costs a few thousand dollars. Use the calculator for a range that matches your finish and location.

How thick should a concrete slab be?

Four inches is common for patios and walkways. Driveways and garage slabs are often 5 to 6 inches, and heavy loads may need more plus reinforcement.

Is it cheaper to mix concrete myself?

Bagged mix works for small jobs, but for anything large, ready-mix delivered by truck is faster and gives a more consistent result.

Does this include demolition of an old slab?

No. Removing an existing slab is a separate cost that depends on thickness, reinforcement and disposal fees.

More calculators

Results are planning estimates based on typical U.S. ranges and the numbers you enter. They are not quotes or professional advice. Last reviewed October 2026.